Custom Made 420 pitch for lightweight race conversions or for Grom with CBR 250/300cc engine swaps! Match this up with a 420 chain and rear sprocket for the complete conversion!...
Chimera Thumb Screw allows you to gain access quickly and easily to the compartment under the OEM seat without a tool! The under-seat compartment allows you to store paper work,...
Aluminum bolt on fuel pump bracket for Mikuni DF-44 vacuum fuel pump. This will allow the DF44 fuel pump to mount on the original fuel pump location on the Honda...
All the details matter! Down to the nuts and bolts, such as these beautiful Chimera Engineering "Jimmy's Nut" Closed-End FRONT Axle Nuts for Super 73 Z1/S1/S2/ZX! Made 100% in the...
This will give you approximately 2-inch rise and will give your carb the correct angle when you run it facing forward. Trimming the fan shrouds or plastic is not needed....
Chimera Engineering Headlight Bracket for Super 73 (ALL MODELS). This bracket would allow you to install common headlights with a single mounting bolt mount. You could mount a motorcycle headlight...
Chimera Engineering High Output Stator - Honda Grom 125 (2014-2020). Load up your Grom 125 with additional lights or electronic accessories without the worry of power supply issues! This stator...
Looking to lower the rear of your Kawasaki Z125 after you've added a Chimera stretch kit to the stock swingarm? This is the rear shock lowering link you need to...
Chimera Engineering Billet Handlebar Grips, universal fit for 7/8" handlebars, perfect for EBikes, Scooters, Honda Motocompacto, and all other thumb throttle bikes/ebikes. Easy to install with two set screws to...
Chimera Engineering Rear Bottom Mount Caliper Brembo P32/P34 Stunt Caliper Adapter - Honda Grom 125 (all years)This will mount your rear brembo caliper below the swingarm.Available in Hard Anodized Black!Chimera...
Chimera Engineering Gas Cap Honda Ruckus Cub 125 Keyless Gas Cap for your Honda Ruckus / Cub 125 / NAVIAvailable Colors: Black Blue Gold Red Silver Yellow 100% Made in...
Chimera Engineering ZS190 Engine Swap Mount Kit for SSR Razkull and Honda Grom 125 4 Speed (2014-2020) ! This is the bracket to mount the Zongshen 190 engine to the...
Chimera LED Tail Light kit for Honda Ruckus! Directly mount this under your Ruckus seat! Ready to install, completely plug and play! Note: Trimming the large hoop tab under...
MUST SELECT FROM THE PRODUCT OPTIONS TO COMPLETE THE KIT PRODUCT OPTIONS EXPLAINED: Select the Chimera Hood Shroud Color (+$50) The Baja Designs Squadron LED light has three options. SPORT...
Will Not Fit Talaria Sting R MX4. Illuminate your path on the Sur Ron LBX / Talaria Sting MX3 / Eride Pro using the Chimera X Baja Designs S2 Sport/Pro...
Chimera Spacer set for Front Honda Grom Wheel with Feign / NCY Forks Set Up.Available in Hard Anodized BlackChimera Spacer set for Front Honda Grom Wheel with Feign / NCY...
Chimera Engineering front brake caliper bracket for 2014-2020 Honda Grom 125 / MSX 125 (non-ABS). Will ONLY accept Brembo 40mm/4-Piston calipers and STOCK sized rotor.Available in hard anodized black! Chimera...
Chimera Engineering Black Handlebar Riser for 2017+ Honda Rebel 300/500. Chimera Engineering Risers requires 1/2" I.D. bushings since the riser bolts are 1/2", you may find them here: Chimera Solid...
Chimera went above and beyond to create the most lightweight aluminum part that could be added to the Talaria Sting! The design not only looks fantastic but also avoids adding...
Chimera "FC" Clip-On Handle Bar Plate - Kawasaki Z125 Pro (all years). The FC clip-on handlebar plate would allow you to use any clip-on motorcycle handlebars that are 35mm ID!...
Chimera Engineering silicone couplers! Perfect and durable replacement over the rubber couplers, which usually cracks and causes an air leak. The Chimera coupler inside diameter is 30mm which steps up...
Honda Signal Plug Converters enable you to plug in aftermarket signals into your harness without doing any cutting, splicing, or wiring. These connectors will plug into the front signal harness...
Chimera Engineering CNC clutch pressure plate is made from T-6061 aluminum! Chimera clutch plate is a direct replacement from the weak cast aluminum OEM unit that generally breaks when stiffer...
Chimera Spacer set for Front Wheel with Feign / NCY Forks Set Up - Honda Ruckus. Please see the information below for fitment details!CONTENT: 2x Axle Spacers 12mm I.D. 2x...
Chimera Engineering 8mm 7075 Aluminum Closed-End (Acorn) Head Stud Nuts! Replaces the engine's ugly head stud nuts and at the same time, helps pull heat from the head studs as...
Chimera M24 Ruckus Front Fork Adapter for Honda Grom 125! This adapter kit will allow you to convert and run any Ruckus front forks, from RRGS, NCY, Feign, etc. To...
NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLESChimera GET High Rise overhead header for 2002-2022 Honda Ruckus NPS50, 1st generation 2002-2012 Honda Metropolitan CHF50!...
Honda = Fun! There’s no doubt about it, and the Honda Motocompacto is no exception! It’s small, compact, fun, and best of all, customizable! However, the OEM Honda Motocompacto headlight...
The Chimera Engineering Billet "TRUST" Sprocket Cover is a perfect fit for Honda GROM (2014-2020) and Monkey 125 (2019-2020). It also fits all 4 speed GROM based engines on the...
