Custom Douglas 12x5 3+2 4x140mm Solid Dish Rim Honda Ruckus Metropolitan Mini Fatty

Custom Douglas 12x5 rear rim that has been machined to fit Kymco drum hubs with a 4x140mm bolt pattern! These are perfect for 2002-2010 Honda Ruckus and custom 2002-2012 Honda Metropolitan with Ruckus swing arm conversion! Dish rims are simple, clean, and classy! It will match any style builds! Perfect for those that don't want any designs or cuts on the rims! Made in the U.S.A!

Please read below for additional information!

Custom machined Douglas 12x5 rim that is most commonly used on the rear of a custom Honda Ruckus or custom Honda Metropolitan. 3+2 offset means you don't need to offset the engine to run this rim. Directly mount this onto a Ruckus along with a Kymco rear hub!

For 1st Gen Honda Metropolitan (NCH50), you would need to convert to a Ruckus swing arm to run a 12" rim.

Spec:

• Diameter: 12"
• Width: 5"
• Bolt Pattern: 4x140
• Polished T-6061 Aluminum!
• Made in the U.S.A!

Note: These Douglas 12x5 rims were machined so that it would work with the Kymco Rear Hubs without any additional modification to the Kymco hub. The center bore diameter hole on these rims are machined larger so that it would fit the center bore step of the hub, making these rims hub-centric. The bolt holes are oblong/oval so that it would be the correct 4x140mm bolt pattern. Flat washers or dress up washers are highly recommended to cover these holes. The bolt holes being oblong will NOT hinder the integrity of the wheel, it's solely visual only, hence the reason why we recommend running washers under the bolts to cover it.

The Kymco Hub and this 12x5 rim will sit slightly off-center to the right approximately 3/8". You could adjust the left side engine bushing to accommodate this OR you could run it as-is and it will ride fine, it'll just look a little off-center to the right, only if you look hard you'll notice.

Due to machining, there may be some small scratches around the rims. Mirror/show polishing service is available for an additional $60 + a 5 days lead time.

FAQ:

1. Will I need to offset my engine?

• No, you do not need to offset the engine. The rim will mount onto a stock Ruckus.

• No, you do not need a stretch kit. The rim will mount onto a stock Ruckus.

• Yes, please see the information listed below for additional parts required.

ADDITIONAL PARTS THAT'S REQUIRED:

-Honda Ruckus

• Kymco 4x140mm Rear Hub (PN: ATR-1003)
• Remove the existing studs on the Kymco hub and run M8x1.25x35mm bolts w/a flat or dress up washer.
• 12" Tire, 130/70-12 and 120/70-12 are very common, however, if you want to run the widest width tire, a 140/70-12 would be used (the side of the tire may rub against the rear shock).

- 2002-2012 Honda Metropolitan (NCH50)

• Kymco 4x140mm Rear Hub (PN: ATR-1003)
• Remove the existing studs on the Kymco hub and run M8x1.25x35mm bolts w/a flat or dress up washer.
• 12" Tire, 130/70-12 and 120/70-12 are very common, however, if you want to run the widest width tire, a 140/70-12 would be used (the side of the tire may rub against the rear shock).
• Ruckus Swing Arm (contact us to see if we have any used Ruckus swing arms available).

Douglas rims are made from spun aluminum, which is originally designed to be used with off-road vehicles, such as ATV and UTV. All Douglas rims have a slight wobble or run-out since they are designed for off-road vehicles that are used on the sands. It's industry standard for spun rims to have some run-outs. After 10+ years of using Douglas rims on custom Ruckus and Scooters, we do not notice any issue with them.